Please use this identifier to cite or link to this item: http://hdl.handle.net/11455/71353
DC FieldValueLanguage
dc.contributor.authorLin, M.C.en_US
dc.contributor.authorChang, L.S.en_US
dc.contributor.authorLin, H.C.en_US
dc.contributor.authorYang, C.H.en_US
dc.contributor.authorLin, K.M.en_US
dc.date2006zh_TW
dc.date.accessioned2014-06-11T06:01:15Z-
dc.date.available2014-06-11T06:01:15Z-
dc.identifier.issn0257-8972zh_TW
dc.identifier.urihttp://hdl.handle.net/11455/71353-
dc.description.abstractThe test specimens of NiCrBSi coating were prepared using the high velocity oxy-fuel spraying technique with a post-thermal treatment. Their high-speed slurry erosion characteristics have been systematically studied. SUS304 stainless steel was selected as the comparison material. Experimental results show that the NiCrBSi sprayed coating exhibits a much better slurry erosion resistance than the SUS304 stainless steel. The erosion rate for the NiCrBSi sprayed coating slightly increases with the impinged angle. However, a maximum erosion rate appears at an impinged angle of around 30 degrees for SUS304 stainless steel. Both NiCrBSi sprayed coating and SUS304 stainless steel exhibit impinged surfaces with lots of furrows at an impinged angle of 30 degrees. At a high impinged angle of 90 degrees, the SUS304 stainless steel exhibits an impinged surface with lots of overlapping and irregular concavities, while, these features are less obvious for NiCrBSi sprayed coating. The hardness of SUS304 stainless steel increases significantly with increasing impinged angle during the high-speed slurry erosion. But, there is no obvious work hardening for the NiCrBSi sprayed coating due to its extra-high hardness and less plastic deformation, even at a high impinged angle of 90 degrees. (c) 2006 Elsevier B.V All rights reserved.en_US
dc.language.isoen_USzh_TW
dc.relationSurface & Coatings Technologyen_US
dc.relation.ispartofseriesSurface & Coatings Technology, Volume 201, Issue 6, Page(s) 3193-3198.en_US
dc.relation.urihttp://dx.doi.org/10.1016/j.surfcoat.2006.06.040en_US
dc.subjectNiCrBSi coatingen_US
dc.subjecthigh velocity oxy-fuel sprayingen_US
dc.subjecthigh-speed slurryen_US
dc.subjecterosionen_US
dc.subjectcavitation erosionen_US
dc.subjectductile metalsen_US
dc.subjectwear behavioren_US
dc.subjectsand erosionen_US
dc.subjectlaseren_US
dc.subjectperformanceen_US
dc.subjectparticlesen_US
dc.subjectvelocityen_US
dc.subjectalloysen_US
dc.subjectmodelen_US
dc.titleA study of high-speed slurry erosion of NiCrBSi thermal-sprayed coatingen_US
dc.typeJournal Articlezh_TW
dc.identifier.doi10.1016/j.surfcoat.2006.06.040zh_TW
item.openairecristypehttp://purl.org/coar/resource_type/c_18cf-
item.openairetypeJournal Article-
item.cerifentitytypePublications-
item.fulltextno fulltext-
item.languageiso639-1en_US-
item.grantfulltextnone-
Appears in Collections:期刊論文
Show simple item record
 

Google ScholarTM

Check

Altmetric

Altmetric


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.